This remote control alarm is operated by multi code remote control.
Entry point protection of doors, boot and bonnet with a shock sensor.
Audible warning is achieved via a standard 115dB siren, visually via
the vehicle indicators and via a dash mounted high intensity red LED.
The system may provide keyless entry and a source of immobilisation
NOTE: Auto - Arming (Anti-Hijack Function)
The system will auto arm 30 seconds after the system has been disarmed.
While the ignition is on the 30 second countdown is reset.
This feature is programmable.
The auto - arming function can be disabled - refer option 3 within the
owners manual at the bottom of the page.
Boot release pulse goes high for approximately 1 second - irrespective
of button press duration.
NOTE: The factory default PIN for this alarm is 2,4
Operation
Arming procedure while ignition is off
The system will arm immediately if the main button of a valid remote
control is momentarily pressed, the doors will lock and all security
functions will become active
Disarming procedure
The system will disarm when the main button of a valid remote control is pressed
Immobilisation
Immobilisation Circuit
The system features a 30 Amp rated, normally closed immobilisation circuit,
which breaks engine critical signals in the vehicle. Starter motor, fuel pump,
fuel injection, main ignition are commonly immobilised circuits
Safety circuitry in case of power failure
System sources alternate power from ignition if main power is lost
Component protection against harsh road conditions
All relays are fully encapsulated to provide protection against dust and moisture
Controllers
System memory
Allows system to track two controllers
Controller re-programming
Service technician can delete lost or stolen controllers from memory
Wiring
Plug and play for service
Designed to allow easy access for service technicians. Plugs and sockets
are located inside the main control module to protect against access by thieves
Override
Emergency Personal Identification Number (PIN) override
Enter the secret two digits to override the immobiliser
Alterable PIN
A factory programmed PIN comes standard with each system.
It is recommended the owner of the system changes the PIN
to a new, easily remembered number
Visual Output
Super bright red dash LED
This LED flashes to inform user when system is armed. The LED is mounted
on the driver's side dash and is visible from outside the window
Arm/Disarm confirmation
System flashes car indicators when arming or disarming
Alarm illumination
System flashes car indicators when thief triggers alarm
Trigger diagnostics
System will flash indicators to report the last triggered circuit
Audio Output
Standard siren
Uses standard two wire 115dB siren
Arm/Disarm confirmation
System sounds a siren when arming and disarming
Temporary arm/disarm chirp disable
Momentarily press the second button of the remote control before pressing
the main button, the siren will not chirp during that one operation
Intrusion Detection
Doors, bonnet and boot monitoring
Triggers alarm system if intruder opens any protected entry point in vehicle
Accepts plug-in single stage shock sensor
Sensor measures vibration subjected to vehicle to detect intruder,
03-009 (refer below link for this part)
Central Locking
Locks and unlocks all doors
System can trigger factory central locking, aftermarket central locking or
central locking relays
Variable pulse time
Extend pulse length to drive pneumatic central locking systems (Mercedes)
Automatic re-locking
System will re-arm and re-lock doors if previously disarmed by remote
control and doors remain closed
Anti-hijacking protection
System locks doors when ignition is turned on, unlocks when ignition is turned off
Specifications
Current draw
Wide Operating voltage
Operating voltage +9VDC to +15VDC
Operating temperature
-20 degrees to +85 degrees for equipment designed to be installed within vehicle cabin
Operating temperature
-20 degrees to +105 degrees for equipment designed to be installed inside
engine compartment
Polarity protection
The system circuitry is design to protect itself against accidental battery
polarity reversal. This can happen when replacing the vehicle battery
Independent indicator power fuse
System uses independent fuse to power indicators, ensures short circuit
in indicator circuit does not affect system operation
Short circuit protection
The power supply wire to the system is protected against an internal
fault within the system
Convenience Functions
Panic / Car Finder
Press and hold second button of remote control to cause siren to sound
and indicators to flash
Electric window closer
Provides signals used by electric window closers, system will close all
electric windows when armed by remote control
Electronic boot release
Press and hold the secondary remote control button to activate boot
release output. The indicators will flash four time each time the boot
release signal is sent
Standards Compliance
Manufactured in ISO9001 facility
Built within world standard production facility